Under-Sink Instant Hot Water Dispenser Manual

1. In start-up mode, briefly press the SET button.

This indicates the temperature setting, with 14 temperature settings from 45°C to 98°C.

One press adjusts the temperature by 10°C; after 85°C, it jumps directly to 90°C. From 90°C to 98°C, one press adjusts by one degree.

2. In start-up mode, press and hold the SET button for more than 2 seconds. This indicates the reheating setting button, with 4 preset temperatures: -3°C, -5°C, -7°C, and -9°C. A short press activates the auto-setting mode, with the default being 5°C reheating.

3. In off-power mode, pressing and holding the SET button for more than 5 seconds confirms the filter lifespan as 3kL or 5kL. The preset value is 5kL.

1. This diagram shows the power on/off button. Press and hold the button for more than 1 second to power on/off.

2. In power-on mode, press and hold the button 5 times consecutively, with intervals of less than 0.5 seconds, to clear the flow meter data (reset).

1. In power-off mode, press and hold both buttons simultaneously for more than 3 seconds to display the current software version.

2. In startup mode, press and hold both buttons simultaneously for more than 3 seconds to automatically switch to °F or °C.

1. Power cord not plugged in properly or loose

2. Water dispenser leakage circuit breaker tripped or fuse blown

3. Indoor fuse blown, circuit breaker tripped, power outage

1. Ensure the wall socket is plugged in.

2. The water dispenser may be leaking electricity. Please unplug it and turn off the water supply, and contact a repairman.

3. Do not increase the fuse capacity.

4. If the problem is caused by an overload, please have a qualified electrical technician handle it.

1. Insufficient water supply

2. Water supply pipe kink

3. Clogged filter preventing water supply

4. Large water withdrawals in a short period, resulting in insufficient replenishment

1. Please check the other faucet in the house.

2. Straighten the water supply line to ensure smooth water flow.

3. Please replace the filter media or contact a repair technician.

4. Wait for the water level to return to normal.

1. The water dispenser is out of water and cannot dispense water.

2. There is air in the hot water pipe.

3. The inlet valve is closed.

4. The inlet pipe is twisted or blocked.

1. Please refer to the troubleshooting steps for "E3 displayed, water shortage light on".

2. Repeatedly press the power button → hot water button to expel air.

3. Open all water inlet valves.

4. Ensure the pipes are not twisted or knotted, preventing flow restriction.

5. Remove and clean the aerator.

6. Flush all pipes to confirm smooth water flow.

1. Start the temperature setting and set the heating temperature.

2. The water dispenser is out of water and cannot heat; the water shortage light is on.

3. A large amount of boiling water was dispensed at once.

4. Internal parts of the water dispenser are faulty.

5. The electronic display screen is not powered on or the plug is not inserted.

1. Please refer to the troubleshooting instructions for "E3 error code, water shortage light on".

2. Ensure the power cord is properly plugged in.

3. Please contact a technician for on-site repair.

4. Ensure the circuit breaker and fuse are functioning correctly.

5. Restart the unit and set the temperature to confirm heating.

1. Press the hot water button on the electronic faucet to release hot water.

2. Adjust the temperature on the screen to a lower value.

3. Check the water collection box for blockages.

4. Remove any air from the Venturi box.

5. Refill the heating tank.

1. The hot water output is low; the water collection box does not have enough time to generate negative pressure, and the outlet is blocked.

2. The inlet solenoid valve may be blocked due to impurities in the inlet pipe.

1. Drain at least 1L of hot water to ensure the water collection box is working.

2. Remove and clean the aerator outlet.

3. Contact a repair technician for on-site repair.